Engines · Infrastructure and project blueprints, energy first

AssetEngine

For infrastructure and project blueprints, starting with energy. AssetEngine turns a site file and a target into a pre-feasibility blueprint: the system architecture, the operating workflow, the sizing, the cost and the schedule. Blueprint in hours, validated in days.
Book a 72-Hour BootcampTalk to us about a project blueprint
Fig 1.1AssetEngine: the sun low on the 50° diagonal over a fine site grid. No site-area figures are shown.

What it does

What AssetEngine does.

AssetEngine is strategy1's engine for infrastructure and project blueprints, energy first. AI agents and strategists turn a site file and a target into a pre-feasibility blueprint covering system architecture, workflow, sizing, CAPEX/OPEX and schedule. A red team challenges it and a chartered engineer signs before release. Every output is stamped pre-feasibility, not bankable engineering.

strategy1 methods it applies

  • LCOE
  • NPV / IRR / DSCR
  • Techno-economic sizing
  • Multi-criteria site scoring
  • Monte Carlo ranges

Each deliverable names the method it used.

  1. 01System architecture
  2. 02Workflow
  3. 03Sizing
  4. 04CAPEX/OPEX
  5. 05Schedule
Two large power transformers standing side by side on gravel pads at an electrical substation under an overcast sky.

What goes in, what you receive

4 deliverables, one decision.

Every input is recorded with its source. Every plan ships with its red-team report.

What goes in

  • 01Your site files (KML, surveys)
  • 02Solar and weather resource data from public atlases
  • 03Equipment datasheets
  • 04National and state power-sector rules and tariffs
  • 05Your capacity, firm-power and tariff targets

Engine

AssetEngine

  • Strategist pod
  • AI agents
  • Calculation code we test ourselves
  • Red team

Working from your Strategy Twin

What you get

  • 01Pre-feasibility blueprint, marked “not bankable”
  • 02Ranked site shortlist with evidence, where site selection is in scope
  • 03Red-team report
  • 04Chartered-engineer sign-off
Fig 2.1What goes into AssetEngine, and what you receive.

How a blueprint is built

Nine steps from site file to signed blueprint.

  1. 01Site screen
  2. 02Solar resource
  3. 03Energy yield
  4. 04Storage sizing
  5. 05Grid screen
  6. 06Economics (LCOE, IRR, DSCR)
  7. 07Rules and permits
  8. 08Red team and sign-offHuman gate
  9. 09Report

Scope in energy

  • Hybrid solar + BESS
  • Wind
  • C&I rooftop and open access
  • EV charging hubs
  • Green-hydrogen pre-feasibility

Typical buyers

  • Independent power producers
  • EPCs
  • C&I power buyers
  • Infrastructure funds

How the engine runs

Six stages. Three points where a person signs.

Every run follows the S1 Method. Humans hold the gates; AI does the heavy lifting between them.
Fig 3.1The S1 Method: six stages, three human gates. Humans hold the gates; AI does the heavy lifting between them.

Stage 01 of 06

Sense

AI does
Reads your documents and systems, and public market, competitor and regulatory data.
People do
A Forward Deployed Strategist frames the decision and the success metric with you.
Output
Problem brief and data inventory.
Indicative time
Hours

Times are indicative for a single Engine Sprint.

Read the S1 Method

The agent team inside AssetEngine

What each agent can and cannot do
  • 01Orchestrator
  • 02Research
  • 03Data & ontology
  • 04Modelling & finance
  • 05Domain specialist
  • 06Red team
  • 07Narrative
  • 08Governance & audit

Controls

The rules this engine works under.

  1. 01A chartered engineer signs before release.
  2. 02Every output is stamped pre-feasibility.
  3. 03A land-use check runs before any yield work: if declared capacity and site area disagree with the norm of roughly 4–5 acres per MW, the report stops until a person records the explanation.

Limit

A blueprint is not bankable engineering. Yield simulation, grid studies, geotechnical surveys and protection design still need licensed engineers.

Red teamWhere a blueprint stops
  1. 01Declared capacity and site area disagree with the norm of roughly 4–5 acres per MW: the report stops until a person records the explanation.
  2. 02A chartered engineer has not signed: nothing is released.
  3. 03Bankable engineering is needed: yield simulation, grid studies, geotechnical surveys and protection design go to licensed engineers.

Sample output

Sample in preparation

An anonymised pre-feasibility pack: architecture diagram, operating workflow, system sizing and schedule.

Request a walkthrough

Strategy types served

3 strategy types delivered through AssetEngine.

AssetEngine is the engine behind solar and BESS pre-feasibility, site selection and energy transition strategy. Each strategy page sets out the decision, what you receive and when that strategy fails.

Industries

Where AssetEngine applies.

The method stays the same; the model of your world changes.

Proof

Compression you can measure.

Our first AssetEngine case is being documented with its baseline. It will be published with the client's permission.

How we measure: the Compression IndexAll proof

Questions

About AssetEngine

What does AssetEngine deliver?

AssetEngine delivers: pre-feasibility blueprint, marked “not bankable”; ranked site shortlist with evidence, where site selection is in scope; red-team report; and chartered-engineer sign-off. Every input is recorded with its source in the evidence ledger, and every plan ships with its red-team report. Each deliverable names the method it used, such as LCOE or NPV / IRR / DSCR.

Which strategy types does AssetEngine cover?

AssetEngine delivers 3 of strategy1's 26 strategy types: Asset / project blueprint, Site & location selection and Energy transition & ESG. It applies across Energy & infrastructure, Real estate, Manufacturing and Healthcare & wellness. The method stays the same in each sector; the model of your world changes. Each strategy page sets out the decision, what you receive and when that strategy fails.

Who signs AssetEngine's conclusions?

A chartered engineer signs every blueprint before release, and every output is stamped pre-feasibility. Every AssetEngine run follows the S1 Method: the Strategy Council and a Domain Fellow sign the decision memo, and your named owner accepts each action before anything reaches your systems. Domain Fellows are chartered engineers, CAs, lawyers and sector veterans who sign the parts that carry professional liability.

How do I start with AssetEngine?

Start with the free Strategy Readiness Scan, which takes 30–60 minutes and suggests an entry engine. The 72-Hour Strategy Bootcamp works one real problem to a working strategy in 3–5 days for a fixed fee. An Engine Sprint runs AssetEngine at full depth in 1–3 weeks for a fixed fee, with your Bootcamp fee credited.

Which projects does AssetEngine cover first?

AssetEngine starts with energy: hybrid solar plus BESS, wind, C&I rooftop and open access, EV charging hubs and green-hydrogen pre-feasibility. Typical buyers are independent power producers, EPCs, C&I power buyers and infrastructure funds. A blueprint is not bankable engineering: yield simulation, grid studies, geotechnical surveys and protection design still need licensed engineers.

How we work

The rules every engine follows.

  1. 01

    Every number traceable.

    Each figure links to its source, date and confidence grade (A, B or C).

  2. 02

    Every plan red-teamed.

    Each strategy ships with its strongest counter-arguments and the conditions under which it fails.

  3. 03

    Signed where it matters.

    Domain Fellows, who are chartered engineers, CAs, lawyers and sector veterans, sign the parts that carry professional liability.

  4. 04

    Nothing written without approval.

    No decision reaches your systems until your named owner accepts it.

Bring one real decision.Leave with a signed plan.

A 72-Hour Bootcamp takes one problem your team would scope in weeks and works it to a decision memo your leadership signs. Fixed scope, fixed fee.

Book a 72-Hour BootcampGet a free Readiness Scan